Q Clamp® Standard Range - 224 - VARIABLE ANGLE IN LINE CONNECTOR A variable angle in line connector (110° -180°) Ideally suited for use between the vertical end post and sloping top rail on stair...
Q Clamp® Standard Range - 199 SINGLE LUGGED BRACKET Often used for mounting boards practically flush with tubes. Fixing holes suit a wide range of common mechanical and chemical masonry anchors.The tube cannot be joined within...
Q Clamp® Standard Range - 191 RIDGE FITTING Designed for use in conjunction with the 185 for roofing applications on small structures. Size Reference Tube diameter (O/D) Nominal bore 1 26.9mm ¾" 2 33.7mm 1"...
Q Clamp® Standard Range - 185 EAVES FITTING Designed for use in conjunction with the 191 for roofing applications on small structures. Size Reference Tube diameter (O/D) Nominal bore 1 26.9mm ¾" 2 33.7mm...
Q Clamp® Standard Range - 184 - GALVANISED PLUG A galvanised stop end for use in the end of tubes. This stop end can be used in either medium or heavy gauge tube. This...
Q Clamp® Standard Range - 171 - DOUBLE SIDED MESH PANEL CLIP Double location weldmesh panel clip. The slotted design of the panel clip enables adjustment in the location of the mesh panels. Supplied with...
Q Clamp® Standard Range - 170 - SINGLE SIDED MESH PANEL CLIP The slotted design of the panel clip enables adjustment in the location of the mesh panels. Supplied with M6 x 30mm long nut...
Q Clamp® Standard Range - 165 - COMBINATION SOCKET A combination fitting designed for use in the construction of racking systems. The fitting enables the connection of a vertical upright at 90° to two horizontal rails....
Q Clamp® Standard Range - 161 - OFFSET 90° CROSSOVER A 90° offset crossover fitting. The tube is unable to be jointed within this fitting. Ideal applications are for racking systems or offset guardrail Size Reference...
Q Clamp® Standard Range - 160 - RETRO FIT CLAMP ON TEE Offset add on tee. Used for making additions to, upgrading or modifying an existing structure without having the need to dismantle part or all...
Q Clamp® Standard Range - 158 4 WAY CROSS A 4 way cross that enables the vertical to pass through the centre of the fitting with the four horizontal tubes joining at 90° to each other....
Q Clamp® Standard Range - 148 - SHORT SWIVEL INLINE TEE NOTE: When using Q clamp 148 fittings for the top rail of a guardrail,the top of the upright must NOT be reduced in length...
Q Clamp® Standard Range - 147 - OFFSET SWIVEL TEE An internal swivel tee used in conjunction with other Q clamp fittings in the range to create a 360° swivel joint. Ideal use on handrail...
Q Clamp® Standard Range - 145 - NON STRUCTURAL OFFSET SIDE PALM FIXING This fitting is designed for palm fixing guardrailing and balustrading to walls, parapets, steps and ramps. Size Reference Tube diameter (O/D) Nominal...
Q Clamp® Standard Range - 140 - Gate Hinge Male section of a two part gate hinge.Used in conjunction with Q clamp fitting reference 138. Size Reference Tube diameter (O/D) Nominal bore 1 26.9mm ¾" 2...
Q Clamp® Standard Range - 138 - Gate Eye Inline Add on Tee. Used for making additions to upgrading or modifying an existing structure without having the need to dismantle part or all of that structure....
Q Clamp® Standard Range - 135 - Retro Fit Clamp On Tee Inline Inline Add on Tee. Used for making additions to upgrading or modifying an existing structure without having the need to dismantle part...
Q Clamp® Standard Range - 134 - GROUND SOCKET A ground socket cast into concrete which is flush to the finished ground level. The upright is held in place using the grubscrew but can easily...
Q Clamp® Standard Range - 130 - ADJUSTABLE CROSS Freely adjustable cross between 30° and 45°. Typical use is as a cross connection on angled mid/lower rails on steeper sloped or stairs with the upright...